Linux version 2.6.19 (root@Knoppix) (gcc version 4.1.2 20061028 (prerelease) (Debian 4.1.1-19)) #7 SMP PREEMPT Sun Dec 17 22:01:07 CET 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f000 (usable) BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved) BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ff60000 (usable) BIOS-e820: 000000001ff60000 - 000000001ff79000 (ACPI data) BIOS-e820: 000000001ff79000 - 000000001ff7b000 (ACPI NVS) BIOS-e820: 000000001ff80000 - 0000000020000000 (reserved) BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. Entering add_active_range(0, 0, 130912) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 130912 HighMem 130912 -> 130912 early_node_map[1] active PFN ranges 0: 0 -> 130912 On node 0 totalpages: 130912 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 990 pages used for memmap Normal zone: 125826 pages, LIFO batch:31 HighMem zone: 0 pages used for memmap DMI present. ACPI: RSDP (v002 IBM ) @ 0x000f6d30 ACPI: XSDT (v001 IBM TP-1P 0x00001330 LTP 0x00000000) @ 0x1ff6edb7 ACPI: FADT (v003 IBM TP-1P 0x00001330 IBM 0x00000001) @ 0x1ff6ef00 ACPI: SSDT (v001 IBM TP-1P 0x00001330 MSFT 0x0100000e) @ 0x1ff6f0b4 ACPI: ECDT (v001 IBM TP-1P 0x00001330 IBM 0x00000001) @ 0x1ff78ed2 ACPI: TCPA (v001 IBM TP-1P 0x00001330 PTL 0x00000001) @ 0x1ff78f24 ACPI: BOOT (v001 IBM TP-1P 0x00001330 LTP 0x00000001) @ 0x1ff78fd8 ACPI: DSDT (v001 IBM TP-1P 0x00001330 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x1008 Allocating PCI resources starting at 30000000 (gap: 20000000:df800000) Detected 599.513 MHz processor. Built 1 zonelists. Total pages: 129890 Kernel command line: ramdisk_size=100000 init=/etc/init lang=us apm=power-off vga=791 initrd=minirt.gz nomce loglevel=0 quiet BOOT_IMAGE=knoppix BOOT_IMAGE=linux Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (0140b000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 513000k/523648k available (2747k kernel code, 10112k reserved, 958k data, 336k init, 0k highmem) virtual kernel memory layout: fixmap : 0xffe16000 - 0xfffff000 (1956 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB) lowmem : 0xc0000000 - 0xdff60000 ( 511 MB) .init : 0xc04a6000 - 0xc04fa000 ( 336 kB) .data : 0xc03aef9c - 0xc049e7b4 ( 958 kB) .text : 0xc0100000 - 0xc03aef9c (2747 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 1200.24 BogoMIPS (lpj=2400488) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 1024K CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00000040 00000180 00000000 00000000 Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. Checking for popad bug... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 16k freed ACPI: Core revision 20060707 ACPI: setting ELCR to 0200 (from 0800) CPU0: Intel(R) Pentium(R) M processor 1300MHz stepping 05 SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Brought up 1 CPUs checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 1188k freed NET: Registered protocol family 16 EISA bus registered ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd936, last bus=5 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 1180-11bf claimed by ICH4 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 Boot video device is 0000:01:00.0 PCI: Firmware left 0000:02:08.0 e100 interrupts enabled, disabling PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Power Resource [PUBS] (on) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices PnPBIOS: Disabled by ACPI PNP intel_rng: FWH not detected SCSI subsystem initialized libata version 2.00 loaded. PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default PCI: Bridge: 0000:00:01.0 IO window: 3000-3fff MEM window: c0100000-c01fffff PREFETCH window: e0000000-e7ffffff PCI: Bus 3, cardbus bridge: 0000:02:00.0 IO window: 00004000-000040ff IO window: 00004400-000044ff PREFETCH window: e8000000-e9ffffff MEM window: c2000000-c3ffffff PCI: Bridge: 0000:00:1e.0 IO window: 4000-8fff MEM window: c0200000-cfffffff PREFETCH window: e8000000-efffffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 196608 bytes) TCP bind hash table entries: 8192 (order: 4, 98304 bytes) TCP: Hash tables configured (established 16384 bind 8192) TCP reno registered Simple Boot Flag at 0x35 set to 0x1 audit: initializing netlink socket (disabled) audit(1195994077.672:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) fuse init (API version 7.8) fuse distribution version: 2.6.1 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered (default) io scheduler cfq registered vesafb: framebuffer at 0xe0000000, mapped to 0xe0880000, using 3072k, total 32768k vesafb: mode is 1024x768x16, linelength=2048, pages=20 vesafb: protected mode interface info at c000:53cf vesafb: pmi: set display start = c00c5463, set palette = c00c54af vesafb: pmi: ports = 3010 3016 3054 3038 303c 305c 3000 3004 30b0 30b2 30b4 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH4: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 ICH4: chipset revision 1 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: ST9100823A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: _NEC DVD+/-RW ND-6500A, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 512KiB hda: Host Protected Area detected. current capacity is 190341925 sectors (97455 MB) native capacity is 195371568 sectors (100030 MB) hda: Host Protected Area disabled. hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 hda3 hda4 hda3: hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 Loading iSCSI transport class v2.0-724.<6>PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice EISA: Probing bus 0 at eisa.0 Cannot allocate resource for EISA slot 1 Cannot allocate resource for EISA slot 2 Cannot allocate resource for EISA slot 3 Cannot allocate resource for EISA slot 4 Cannot allocate resource for EISA slot 5 Cannot allocate resource for EISA slot 6 Cannot allocate resource for EISA slot 7 Cannot allocate resource for EISA slot 8 EISA: Detected 0 cards. Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 15 input: AT Translated Set 2 keyboard as /class/input/input0 Using IPI No-Shortcut mode ACPI: (supports S0 S3 S4 S5) Time: tsc clocksource has been installed. Synaptics Touchpad, model: 1, fw: 5.9, id: 0x2c6ab1, caps: 0x884793/0x0 serio: Synaptics pass-through port at isa0060/serio1/input0 input: SynPS/2 Synaptics TouchPad as /class/input/input1 IBM TrackPoint firmware: 0x0e, buttons: 3/3 input: TPPS/2 IBM TrackPoint as /class/input/input2 RAMDISK: Compressed image found at block 0 EXT2-fs warning: checktime reached, running e2fsck is recommended VFS: Mounted root (ext2 filesystem). Failed initialization of WD-7000 SCSI card! usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 11, io mem 0xc0000000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) usbcore: registered new interface driver libusual usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. ieee1394: Initialized config rom entry `ip1394' ACPI: PCI Interrupt 0000:02:07.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[c0206000-c02067ff] Max Packet=[2048] IR/IT contexts=[4/8] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) ieee1394: sbp2: Try serialize_io=0 for better performance ieee1394: Host added: ID:BUS[0-00:1023] GUID[00061b0020065b8f] Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon! Unable to identify CD-ROM format. VFS: Can't find an ext2 filesystem on dev hda. ReiserFS: hda: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on hda FAT: invalid media value (0x02) VFS: Can't find a valid FAT filesystem on dev hda. ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A cloop: Initializing cloop v2.05 cloop: loaded (max 8 devices) cloop: /cdrom/KNOPPIX/KNOPPIX: 24954 blocks, 65536 bytes/block, largest block is 65562 bytes. cloop: loaded 128 blocks into cache. ISO 9660 Extensions: RRIP_1991A aufs 2.6.19-20061211 aufs rmdir_whtmp:698:aufs_rmdir_whtm[1423]: failed removing .wh..wh.network.0012(-21), ignored aufs do_rmdir_whtmp:732:aufs_rmdir_whtm[1423]: I/O Error, err -21 Freeing unused kernel memory: 336k freed ACPI: AC Adapter [AC] (off-line) ACPI: Battery Slot [BAT0] (battery present) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] ACPI: Sleep Button (CM) [SLPB] Using specific hotkey driver ibm_acpi: IBM ThinkPad ACPI Extras v0.12a ibm_acpi: http://ibm-acpi.sf.net/ ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU] (supports 8 throttling states) ACPI: Thermal Zone [THM0] (35 C) ACPI: Video Device [VID] (multi-head: yes rom: no post: no) Time: acpi_pm clocksource has been installed. cpufreq: No nForce2 chipset. p4-clockmod: Warning: Pentium M detected. The speedstep_centrino module offers voltage scaling in addition of frequency scaling. You should use that instead of p4-clockmod, if possible. p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available powernow: This module only works with AMD K7 CPUs Yenta: CardBus bridge found at 0000:02:00.0 [1014:0528] Yenta: Using INTVAL to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:00.0, mfunc 0x01d11002, devctl 0x64 Yenta: ISA IRQ mask 0x04b8, PCI irq 11 Socket status: 30000007 pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff cs: IO port probe 0x4000-0x8fff: clean. pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xcfffffff pcmcia: parent PCI bridge Memory window: 0xe8000000 - 0xefffffff pcmcia: Detected deprecated PCMCIA ioctl usage from process: cardmgr. pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools. pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details. cs: IO port probe 0xc00-0xcff: clean. cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0x800-0x80f: clean. cs: IO port probe 0x100-0x4ff: excluding 0x3b8-0x3df 0x4d0-0x4d7 cs: IO port probe 0xa00-0xaff: clean. eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel 855PM Chipset. agpgart: AGP aperture is 256M @ 0xd0000000 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt for device 0000:00:1f.6 disabled ieee80211_crypt: registered algorithm 'NULL' ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2 ipw2100: Copyright(c) 2003-2006 Intel Corporation ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 ipw2100: Detected Intel PRO/Wireless 2100 Network Connection e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI e100: Copyright(c) 1999-2006 Intel Corporation pnp: Device 00:0a activated. 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11 ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11 e100: eth2: e100_probe: addr 0xc0205000, irq 11, MAC addr 00:06:1B:CB:CF:00 NET: Registered protocol family 23 pnp: Device 00:0c activated. nsc-ircc, chip->init nsc-ircc, Found chip at base=0x02e nsc-ircc, driver loaded (Dag Brattli) IrDA: Registered device irda0 nsc-ircc, Found dongle: HP HSDL-1100/HSDL-2100 parport: PnPBIOS parport detected. parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1f.5 to 64 intel8x0_measure_ac97_clock: measured 117916 usecs intel8x0: clocking to 48000 NET: Registered protocol family 17 NET: Registered protocol family 10 lo: Disabled Privacy Extensions ADDRCONF(NETDEV_UP): eth2: link is not ready Mobile IPv6 eth1: no IPv6 routers present device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised: dm-devel@redhat.com kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ADDRCONF(NETDEV_UP): eth2: link is not ready [drm] Initialized drm 1.0.1 20051102 ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 [drm] Initialized radeon 1.25.0 20060524 on minor 0 mtrr: 0xe0000000,0x8000000 overlaps existing 0xe0000000,0x2000000 mtrr: 0xe0000000,0x8000000 overlaps existing 0xe0000000,0x2000000 mtrr: 0xe0000000,0x8000000 overlaps existing 0xe0000000,0x2000000 agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode [drm] Setting GART location based on new memory map [drm] writeback test succeeded in 2 usecs eth1: no IPv6 routers present